Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Starting undionly.efi or snponly.efi from the linux command
2018-10-17, 22:46
Post: #5
RE: Starting undionly.efi or snponly.efi from the linux command
shell results

dhcp
Waiting for link-up on net0 .................. Down (http://ipxe.org/38086193)
Waiting for link-up on net1 .................. Down (http://ipxe.org/38086193)
Configuring (net2 00:30:93:0c:22:06) .................. No configuration methods succeeded (http://ipxe.org/040ee186)
Waiting for link-up on net3 .................. Down (http://ipxe.org/38086193)
Waiting for link-up on net4 .................. Down (http://ipxe.org/38086193)
Could not open net5: Input/output error (http://ipxe.org/1d6a4695)

ifstat info.

net0: 00:3e:01:ca:0d:0a . using 14e4-1682 on 0000:0b:00.0 (closed)
[Link:down, TX:0 TXE:0 RX:0 RXE:0]
[Link status: Down (http://ipxe.org/38086193]

net1: 00:3e:01:ca:0d:09 . using 14e4-1682 on 0000:0c:00.0 (closed)
[Link:down, TX:0 TXE:0 RX:0 RXE:0]
[Link status: Down (http://ipxe.org/38086193]

net2: 00:30:93:0c:22:06 . using x540t on 000:19:00.0 (closed)
[Link:down, TX:0 TXE:0 RX:0 RXE:0]
[Link status: Down (http://ipxe.org/38086193]

net3: 00:30:93:0c:22:07 . using x540t on 0000:19:00.1 (closed)
[Link:down, TX:0 TXE:0 RX:0 RXE:0]
[Link status: Down (http://ipxe.org/38086193]

net4: a8:20:66:03:a2:fs . using 14e4-16b0 on 0000:aa:00 (closed)
[Link:down, TX:0 TXE:0 RX:0 RXE:0]
[Link status: Down (http://ipxe.org/38086193]

net5: 74:1b:b2:f2:44:2b . using NII on NII-0000:aa:00 (closed)
[Link:up, TX:0 TXE:0 RX:0 RXE:0]

from lspci on Ubuntu 18.04

0b:00.0 Ethernet controller Broadcom Limited NetXtreme BCM57762 Gigabit Ethernet PCIe
0c:00.0 Ethernet controller Broadcom Limited NetXtreme BCM57762 Gigabit Ethernet PCIe
aa:00.0 Ethernet controller Broadcom Limited NetXtreme BCM57761 Gigabit Ethernet PCIe (rev 10)
19:00.0 Intel Ethernet controller Intel Corporation Ethernet Controller 10-Gigabit X540-ATZ (rev 01)
19:00.1 Intel Ethernet controller Intel Corporation Ethernet Controller 10-Gigabit X540-ATZ (rev 01)


Note: built with a checkout of ipxe on 16 Oct 2018.
Find all posts by this user
Quote this message in a reply
Post Reply 


Messages In This Thread
RE: Starting undionly.efi or snponly.efi from the linux command - ebruno - 2018-10-17 22:46



User(s) browsing this thread: 3 Guest(s)