Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
hang on iPXE initialising devices...
2014-03-04, 16:52
Post: #1
hang on iPXE initialising devices...
I'm using PXElinux 6.03-Pre6 to chain boot iPXE

LABEL ipxe
kernel ipxe.lkrn dhcp && chain http://10.48.128.56/wimboot.ipxe

All I get after selecting the menu entry in PXELINUX is
iPXE initialising devices...

Then it just hard hangs, no CTL-ALT-DEL, have to power cycle.
Any idea why this is happening?
Find all posts by this user
Quote this message in a reply
2014-03-05, 14:51
Post: #2
RE: hang on iPXE initialising devices...
(2014-03-04 16:52)VirtualNobody Wrote:  I'm using PXElinux 6.03-Pre6 to chain boot iPXE

LABEL ipxe
kernel ipxe.lkrn dhcp && chain http://10.48.128.56/wimboot.ipxe

All I get after selecting the menu entry in PXELINUX is
iPXE initialising devices...

Then it just hard hangs, no CTL-ALT-DEL, have to power cycle.
Any idea why this is happening?

It seems to be getting stuck somewhere during device initialisation. Could you try building iPXE with DEBUG=device,pci,undiload,undinet and see what output gets produced?

Thanks,

Michael
Visit this user's website Find all posts by this user
Quote this message in a reply
2014-03-05, 22:10
Post: #3
RE: hang on iPXE initialising devices...
(2014-03-05 14:51)mcb30 Wrote:  It seems to be getting stuck somewhere during device initialisation. Could you try building iPXE with DEBUG=device,pci,undiload,undinet and see what output gets produced?

Thanks for the reply...

I just did a git clone and a make DEBUG=device,pci,undiload,undinet on a RHEL 6.5 system. I copied ipxe.lkrn into my /tftpboot directory.

Now I get:
iPXE initialising devices...Adding 3c509 root bus
Adding PCI root bus

Then the hard hang.

Same result on both a VMware 5.5 virtual and a Dell T3600. Maybe it's because neither of these systems have an old PCI bus?
Find all posts by this user
Quote this message in a reply
2014-03-06, 11:40
Post: #4
RE: hang on iPXE initialising devices...
(2014-03-05 22:10)VirtualNobody Wrote:  I just did a git clone and a make DEBUG=device,pci,undiload,undinet on a RHEL 6.5 system. I copied ipxe.lkrn into my /tftpboot directory.

Now I get:
iPXE initialising devices...Adding 3c509 root bus
Adding PCI root bus

Then the hard hang.

Same result on both a VMware 5.5 virtual and a Dell T3600. Maybe it's because neither of these systems have an old PCI bus?

Does the same problem happen if you load iPXE directly (e.g. PXE->ipxe.pxe), rather than going via pxelinux (PXE->pxelinux->ipxe.lkrn)?

Michael
Visit this user's website Find all posts by this user
Quote this message in a reply
2014-03-07, 07:19
Post: #5
RE: hang on iPXE initialising devices...
Getting this type of behavior as well. Emulex BE2 and BE3, with undionly DHCP Fails. If I load the iPXE ISO on the same hardware, it hangs.

"Thus far, you have been adrift within the sheltered harbor of my patience..."
Find all posts by this user
Quote this message in a reply
2014-03-07, 16:38
Post: #6
RE: hang on iPXE initialising devices...
(2014-03-07 07:19)MultimediaMan Wrote:  Getting this type of behavior as well. Emulex BE2 and BE3, with undionly DHCP Fails. If I load the iPXE ISO on the same hardware, it hangs.

The ISO also goes through syslinux. Does the same problem arise if using a method which bypasses syslinux/pxelinux, e.g. using ipxe.usb?

Michael
Visit this user's website Find all posts by this user
Quote this message in a reply
Post Reply 




User(s) browsing this thread: 2 Guest(s)