Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
|
2019-12-04, 08:53
Post: #1
|
|||
|
|||
Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
It is strange that it is good to load Esxi files, however, it hangs once stepping to load Setup GUI. The last step referring to the screen is "Shutting down firmware services....". I see some people in discussion that iPXE is necessary to enable IMAGE_COMBOOT. however, I failed to make it if enable #define IMAGE_COMBOOT in src/config/general.h. It always prompt me that relocation truncated to fit: R_X86_64_32 against symbol 'com32_farcall' defined in .text.com32_farcall section in bin-x86_64-efi/blib.a(com32_call.o) … etc.
not sure what is wrong, anyway, Esxi installation works well while I am using PXE. The contents on how I tried to boot in iPXE is like, kernel http://myserver/vmware/esxi_6.5.1/efi/boot/mboot.efi -c http://myserver/vmware/esxi_6.5.1/boot.cfg boot The contents of boot.cfg, bootstate=0 title=Loading ESXi installer timeout=5 prefix=http://myserver/vmware/esxi_6.5.1 kernel=tboot.b00 kernelopt=runweasel ks=http://myserver/vmware/esxi_6.5.1/ks.cfg #kernelopt=runweasel modules=b.b00 --- jumpstrt.gz --- useropts.gz --- features.gz --- k.b00 --- chardevs.b00 --- a.b00 --- user.b00 --- uc_intel.b00 --- uc_amd.b00 --- sb.v00 --- s.v00 --- ata_liba.v00 --- ata_pata.v00 --- ata_pata.v01 --- ata_pata.v02 --- ata_pata.v03 --- ata_pata.v04 --- ata_pata.v05 --- ata_pata.v06 --- ata_pata.v07 --- block_cc.v00 --- char_ran.v00 --- ehci_ehc.v00 --- elxnet.v00 --- hid_hid.v00 --- i40en.v00 --- igbn.v00 --- ima_qla4.v00 --- ipmi_ipm.v00 --- ipmi_ipm.v01 --- ipmi_ipm.v02 --- ixgben.v00 --- lpfc.v00 --- lsi_mr3.v00 --- lsi_msgp.v00 --- lsi_msgp.v01 --- misc_cni.v00 --- misc_dri.v00 --- mtip32xx.v00 --- ne1000.v00 --- nenic.v00 --- net_bnx2.v00 --- net_bnx2.v01 --- net_cdc_.v00 --- net_cnic.v00 --- net_e100.v00 --- net_e100.v01 --- net_enic.v00 --- net_fcoe.v00 --- net_forc.v00 --- net_igb.v00 --- net_ixgb.v00 --- net_libf.v00 --- net_mlx4.v00 --- net_mlx4.v01 --- net_nx_n.v00 --- net_tg3.v00 --- net_usbn.v00 --- net_vmxn.v00 --- nhpsa.v00 --- nmlx4_co.v00 --- nmlx4_en.v00 --- nmlx4_rd.v00 --- nmlx5_co.v00 --- ntg3.v00 --- nvme.v00 --- nvmxnet3.v00 --- ohci_usb.v00 --- pvscsi.v00 --- qedentv.v00 --- qfle3.v00 --- qflge.v00 --- qlnative.v00 --- sata_ahc.v00 --- sata_ata.v00 --- sata_sat.v00 --- sata_sat.v01 --- sata_sat.v02 --- sata_sat.v03 --- sata_sat.v04 --- scsi_aac.v00 --- scsi_adp.v00 --- scsi_aic.v00 --- scsi_bnx.v00 --- scsi_bnx.v01 --- scsi_fni.v00 --- scsi_hps.v00 --- scsi_ips.v00 --- scsi_isc.v00 --- scsi_lib.v00 --- scsi_meg.v00 --- scsi_meg.v01 --- scsi_meg.v02 --- scsi_mpt.v00 --- scsi_mpt.v01 --- scsi_mpt.v02 --- scsi_qla.v00 --- shim_isc.v00 --- shim_isc.v01 --- shim_lib.v00 --- shim_lib.v01 --- shim_lib.v02 --- shim_lib.v03 --- shim_lib.v04 --- shim_lib.v05 --- shim_vmk.v00 --- shim_vmk.v01 --- shim_vmk.v02 --- uhci_usb.v00 --- usb_stor.v00 --- usbcore_.v00 --- vmkata.v00 --- vmkplexe.v00 --- vmkusb.v00 --- vmw_ahci.v00 --- xhci_xhc.v00 --- emulex_e.v00 --- weaselin.t00 --- esx_dvfi.v00 --- esx_ui.v00 --- lsu_hp_h.v00 --- lsu_lsi_.v00 --- lsu_lsi_.v01 --- lsu_lsi_.v02 --- lsu_lsi_.v03 --- native_m.v00 --- rste.v00 --- vmware_e.v00 --- vsan.v00 --- vsanheal.v00 --- vsanmgmt.v00 --- btldr.t00 --- tools.t00 --- xorg.v00 --- imgdb.tgz --- imgpayld.tgz build= updated=0 Anybody who can help me? |
|||
2019-12-06, 12:09
Post: #2
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
(2019-12-04 08:53)hugogong Wrote: It is strange that it is good to load Esxi files, however, it hangs once stepping to load Setup GUI. The last step referring to the screen is "Shutting down firmware services....". I see some people in discussion that iPXE is necessary to enable IMAGE_COMBOOT. however, I failed to make it if enable #define IMAGE_COMBOOT in src/config/general.h. It always prompt me that relocation truncated to fit: R_X86_64_32 against symbol 'com32_farcall' defined in .text.com32_farcall section in bin-x86_64-efi/blib.a(com32_call.o) … etc. what is your commandline for the compile. and which compiler are you using? have you searched for your error message on the iPXE mailing list or the forum? Use GitHub Discussions VRAM bin |
|||
2019-12-09, 02:22
Post: #3
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
My command line is "make bin-x86_64-efi/ipxe.efi EMBED=file.ipxe".
The contents of file.ipxe : #!ipxe dhcp chain http://myserver/ipxe/menu/boot.ipxe The compiler I am using, gcc version 6.3.0 20170406 (Ubuntu 6.3.0-12ubuntu2) I searched for the error message regarding "relocation truncated". Some people said to change compile option compile option -O to "-mcmodel=medium". |
|||
2019-12-09, 07:26
Post: #4
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
you can only activate combot in pcbios builds, not efi
Use GitHub Discussions VRAM bin |
|||
2019-12-09, 09:22
Post: #5
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
(2019-12-09 07:26)NiKiZe Wrote: you can only activate combot in pcbios builds, not efi thanks for the reminder, I change make command like: make bin-x86_64-pcbios/ipxe.pxe EMBED=fix.ipxe however, I got a lot error, cc1: error: code model kernel does not support PIC mode cc1: warning: unrecognized command line option '-Wno-address-of-packed-member' Is there a guide on how to make pcbios? |
|||
2019-12-09, 10:10
Post: #6
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
make bin/ipxe.pxe EMBED=fix.ipxe
You probably don't want 64bit anyway. which version of gcc are you using? Use GitHub Discussions VRAM bin |
|||
2019-12-10, 04:03
Post: #7
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
(2019-12-09 10:10)NiKiZe Wrote: make bin/ipxe.pxe EMBED=fix.ipxemy gcc version --> 6.3.0 20170406 (Ubuntu 6.3.0-12ubuntu2) It is fine to make via command "make bin/ipxe.pxe EMBED=fix.ipxe" however, my machine fails to boot into iPXE menu if I replace the previous file "ipxe.efi" with the new one "ipxe.pxe". I renamed ipxe.pxe to ipxe.efi in order not to change anything in DHCP Service. Is there any special settings if using ipxe.pxe file instead of ipxe.efi? |
|||
2019-12-10, 06:49
Post: #8
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
I then would like to refer you to the FAQ, especially the section:
Quote:I'm trying to boot an .efi in bios mode, I'm trying to boot bios code in EFI mode Use GitHub Discussions VRAM bin |
|||
2019-12-10, 07:30
Post: #9
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
(2019-12-10 06:49)NiKiZe Wrote: I then would like to refer you to the FAQ, especially the section: thanks, so is there an sample on how to use ipxe.pxe file? |
|||
2019-12-12, 01:19
Post: #10
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
Anyway, not to consider how to use ipxe.pxe instead of ipxe.efi. This thread is intended to ask how Esxi failed to install via iPXE in UEFI BIOS mode?
I tried kernel or chain. neither of them is fine. 1. kernel http://myserver/vmware/esxi_6.5.1/efi/boot/mboot.efi -c http://myserver/vmware/esxi_6.5.1/boot.cfg boot 2. chain http://myserver/vmware/esxi_6.5.1/efi/boot/mboot.efi -c http://myserver/vmware/esxi_6.5.1/boot.cfg boot It is fine if I use chain in grub via PXE. |
|||
2019-12-12, 06:59
Post: #11
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
I take the reference from here,
https://www.reversengineered.com/2015/02...i-in-ipxe/ |
|||
2019-12-18, 08:51
Post: #12
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
(2019-12-10 07:30)hugogong Wrote:(2019-12-10 06:49)NiKiZe Wrote: I then would like to refer you to the FAQ, especially the section: Hi, NiKiZe Looks iPXE indeeds to have issue to do a Esxi installation with a UEFI BIOS. I tried it both on AMD and Intel platform. Is there any developer I can ask to help to fix it? |
|||
2019-12-18, 16:37
(This post was last modified: 2019-12-18 16:38 by NiKiZe.)
Post: #13
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
I would rather say that:
How would you boot Esxi on a EFI only platform over the network? It seems that it is vmware that don't provide the tools you need. Report the issue with Vmware Or your hardware provider which don't give you a working pcbios fallback Use GitHub Discussions VRAM bin |
|||
2019-12-19, 02:35
Post: #14
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
(2019-12-18 16:37)NiKiZe Wrote: I would rather say that: It is all right to do a network installation with UEFI BIOS via grub+PXE, however, it fails via iPXE and even iPXE chain load grub and then install Esxi. I don't think it is vmware business but iPXE shall provide a workaround for user. |
|||
2019-12-19, 07:26
Post: #15
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
iPXE will only support booting efi files in efi environments, if there is no EFI to boot then there is nothing that can be done.
If there is an EFI that can be booted, but don't work with iPXEs standard stack, then that EFI has bugs that needs to be fixed: workarounds for you: * use iSCSI to boot an efi image, provided that ESX isn't lacking iSCSI support (another bug if so). * abuse wimboots ability to create a virtual FS and run it from there, just send over bootx64.efi and all other files needed for the boot Use GitHub Discussions VRAM bin |
|||
2019-12-20, 09:37
Post: #16
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
(2019-12-19 07:26)NiKiZe Wrote: iPXE will only support booting efi files in efi environments, if there is no EFI to boot then there is nothing that can be done. Any big difference between snponly.efi and ipxe.efi which they are all maked by ipxe source code? I find that it is good to install Esxi if chain snponly.efi instead of ipxe.efi. |
|||
2020-02-13, 14:26
Post: #17
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
you
can only activate combot in pcbios builds, not efi |
|||
2020-02-14, 02:40
Post: #18
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
Not sure it is iPXE or Esxi issue, as UEFI BIOS, I will still hit failure. nothing changes.
|
|||
2020-06-16, 00:56
Post: #19
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
Starting around ESXi 6.7 I could no longer use chain to boot the installer. This is what works for me now:
Code: kernel http://${esxi}/mboot.efi -c http://${esxi}/boot.cfg |
|||
2020-06-17, 02:11
Post: #20
|
|||
|
|||
RE: Why Esxi 6.5 or 6.7 fail to start setup GUI via iPXE
If you stroll up the top of this post, you would see that I used kernel instead of chain as well.
kernel http://myserver/vmware/esxi_6.5.1/efi/boot/mboot.efi -c http://myserver/vmware/esxi_6.5.1/boot.cfg Either ipxe or Exsi shall look into this issue. I still it on desktop platform, however, mobile platform is fine. |
|||
« Next Oldest | Next Newest »
|
User(s) browsing this thread: 1 Guest(s)